Please perform a firmware upgrade. It’s now an automatic switching of the resolution implemented!

Advantage of the automatic switching of the resolution is that the broadcasted signal from the TV- station to the pure flat screen will be forwarded (via HDMI). Disadvantage: The switching from one station to another station with a different resolution lasts much longer, since the flat panel is also at each switch will need to adapt to. Depending on the type of flat panel it can take up to 3 seconds or more before a program with a different resolution is visible.

If you want to use the automatic switching of the resolution switch the "TV resolution" in the video menu (or via the shortcut button on the remote "V. format) to AUTO.

Internal tests have shown that it can be useful let the NanoXX upscale channels in 720p to 1080i because the NanoXX upscaling makes an excellent picture (much better than many flat panels).

Via satellite (and also in cable) HDTV broadcasts are either 720p or 1080i, since for showings with a 1080p resolution at much higher data rates would be needed. The broadcast would be too expensive. The 1080p resolution is therefore of the Blu- ray technology (or similar) reserved.

The NanoXX has for this reason "only" a version 1.2 HDMI port, because the data transmission speed of this version is completely sufficient for the maximum resolution of 1080i. Only for the resolution in 1080p HDMI version 1.3 is required.

In this context we would like to point out that the NanoXX converts the "normal" programs SDTV (Standard Definition) in higher resolutions (optionally) 720p or 1080i. This is the so-called upscaling NanoXX was often praised by the trade press, particularly because of broadcasts in 16:9 SDTV better image quality results are produced. Many customers had reported that in-studio broadcasts of public service broadcasters believed that this transfer would be in HDTV. Prerequisite for a brilliant picture is of course that your flatscreen is connected via HDMI.

The NanoXX sends out all TV and audio signals in parallel.

You can have a flat- TV connected via HDMI to the TV signal and, in parallel, a Dolby amplifier via the optical or the coaxial digital audio output, or via the analog RCA connectors connected. The settings are located in menu -> system settings -> sound settings.

The Dolby signal can also be transferred via HDMI (menu -> audio settings: HDMI Dolby Digital). In this way the audio and video signal is send trough the HDMI- output of your NanoXX directly to your flat- TV or looped trough your HDMI-ready Digital AV- Receiver to the flat- TV. In the second way the AV- receiver’ll play out the digital audio by HDMI as source.

Parallel to the HDMI transmission also the analogue audio and video signal is served via scart output. The video signal via scart (always in 576i) is independent of the HDMI resolution.

Our tip: Connect high-quality flat panels or projectors only via HDMI or YPbPr because the image quality is much better than, for example, the scart connector.

Please perform a firmware upgrade. The query function for entering the PIN was incorrect and was revised. As of firmware version 02.44 this works flawlessly. How to perform a firmware upgrade, please read here: Firmware Upgrade

Note: For some CI modules it’s possible, the PIN query generally to suppress. This can be useful, though generally not for persons under 18 residing in your household.

Go to the CI module  menu. (menu -> Conditional Access) and take the appropriate setting. Please follow the instructions of the CI module manufacturer because we do not support them.

To make a backup of your personal program list and receiver settings go to

menu -> channel settings -> software manager -> yellow key (System & Channel backup).

Since SW version 02.37: You’ll have to select “channel list” as well as “system settings” to save both.

You’ll get two files on the USB Stick for each backup.

The fileextention for system- and  programmlist- backups is ".si"

To restore your saved settings go to menu -> multimedia -> USB and select your saved settings. Press the red button (update) to load these settings to your receiver.

Since SW version 02.37: go to menu -> software manage and select at "channel list" and "system settings" the option "restore" and select the backup files stored on your USB stick.Wait now until the process is finished.

Principle applies to all upgrade and backup operations: Do not disconnect the receiver from power while upgrade is in progress